Forney Uniflame, Forney Uniflame amplifier, Forney, the Uniflame flame amplifier, Forney, the Uniflame flame detector, Forney, Uniflame detector, Forney, the Uniflame flame detector, Forney, the Uniflame flame sensor, Forney, the Uniflame flame relay, Forney, the Uniflame UV flame sensor, Forney, Uniflame processor Forney, Uniflame infrared probe 

 General Machinery International Trading (Shanghai) Co., Ltd. Special Agent Forney, Uniflame amplifier, Forney, the Uniflame flame amplifier, Forney, the Uniflame flame detector, Forney, Uniflame detector, Forney, the Uniflame flame detector, Forney, the Uniflame flame sensor, Forney, the Uniflame flame relay, Forney, Uniflame UV flame sensor Uniflame processor Forney, Forney, Uniflame infrared probe. 
 Forney, PM-DR,-6101E amplifier device is a stand-alone intelligent controller, placed by two Lid base printed circuit board (PCB) composition. A PCB including the combination of power, relay output / input (I / O) interface software. Another PCB, including microprocessors, stabilizer and signal processing and electronic equipment. The whole device can be installed in a single equipment cabinet. 
 Flame detection probe can be equipped with: IDD-II with the filtered infrared probe, the IDD-IIU without the filter of the infrared probe, UV-4 probe, the DR-6 IDD / UV probe. 
 D furnace flame detector Uniflame 95 Series Overview: FORNEY the UNIFLAME series flame detectors using solid-state infrared sensor (IR), ultraviolet sensors (UV) and sensor (IR UV) flame detector based on microprocessor design. Detector with an internal flame relay, and adjust the threshold value of the ON / OFF, so no remote flame amplifier. The UNIFLAME \ 95 series detector both the principles and characteristics of the FORNEY of DPD flame detectors can detect a single burner or combustion control condition the target flame with or without. The UNIFLAME \ 95 series generated by the detector target flame modulation amplitude (ie, flame flicker characteristics). In the detector set-up process, can produce a modulation frequency characteristics of the best flame ON / OFF resolution. Can manually adjust or automatic adjustment to select the appropriate modulation frequency and detector gain. UNIFLAME \ 95 Series detectors with automatic programming (learning) functions; 21 kinds of flame flicker frequency selection; four optional programming file to store settings; also increased by using the user application the FORNEY based WINDOWS95/98/NT software, remote communications capabilities. All UNIFLAME \ 95 detectors require a 24VDC power supply, with 12 cores and quick connectors, electronic self-test function (no longer required mechanical shutter). Detector with an 8-bit number / letter LED display and four buttons, easy for users to observe the operating parameters and select settings. Applications: IR-type: includes an infrared flame sensor, this sensor is suitable for oil and coal fuels. UV-type: includes a UV flame sensor, this sensor is suitable for the situation in the fuel gas and diesel fuel. DS Type: (dual sensor) above both infrared and ultraviolet flame sensor, this sensor is suitable for multi-fuel. Uniflame series Ibid installation accessories: machinery and auxiliary tray flange (required) detector is a direct glimpse of the installation or fiber installation need to use the tray flange, tray flange external interface for the 1 "NPT thread, materials for hard aluminum universal joint universal joint (straight peep optional) detector is used to adjust the viewing angle of detector in the detector is installed insulated pipes (a direct glimpse) pipe insulation is prevent the heat from the heat observation tube reached the detector, the detector with the earth electrical insulation. observation tube is ordered together with the mounting flange. quartz window (direct glimpse optional) quartz window, when the detector need to be sealed or to use when connecting to the quartz window blocks furnace pressure, hot gases and ash, so close to the detector or contaminated lenses. specification is 1 inch U.S. standard taper thread. need to be sealed with a 1-inch three links connected in order to pass cooling air. fiber optic components (fiber type) fiber optic components including catheter components, catheter components, fiber optic components, furnace wall installed components. burner structure is complex and multi-burner burning boilers, the use of fiber optic components to the flame "flash" signal to the furnace through the optical fiber transmission, to facilitate the detector monitoring the electrical auxiliary detector cable FORNEY UNIFLAME \ 95 Series 12 core detector foil shielded cable This cable is 6 # 18AWG and four # 22AWG wire with a pair of # 22AWG twisted pair cable jacket is treated polyolefin materials (flame retardant, low smoke, zero halogen) diameter of 0.43 "(10.9mm). Each detector longest cable up to 1000 feet. The raw rubber cable quick connector as described below. The quick joints UNIFLAME \ 95 series detector factory comes with a 12 core cable connector Yang, the FORNEY can provide the matching cables female connector, easy site installation. Refer to the aviation plug attachment instructions. With adapter cables the FORNEY provide the prefabricated 12-core cable, the length can be scheduled, with a female connector factory. The attachment length range from 10 feet (3m) to 300 feet (91m). Junction box assembly remote communication, and the distance between the the UNIFLAME detector and control room more than 200 feet (61M), each detector must be connected to a junction box. In the junction box, the two communication lines must be separated with 12-core cable access, in the circulation loop, multi-cascading manner (daisy chain) connection to each detector, and finally to the computer. The FORNEY junction box components, lengths range from 3-30 feet (0.9 to 9.1 meters), providing a convenient way of wiring. In the junction box end of the quick connector to the UNIFLAME detector. FORNEY 12 core cable factory with quick connectors, flexible cable can be connected to the other, the terminals in the junction box. The terminal can be connected to 14AWG wire, pressed into the clamp connector can be quickly and securely connected. Through the junction box, the installer can connect all wiring to reach the burner management system in the two lines are not connected, but FORNEY 12 core cable. The two communication lines from the detector must be connected with the upper and lower junction box, and ultimately reach the computer through the two-wire communications cable. 24VDC power supply FORNEY provide 24VDC power supply for 95 series flame detector.